
Layout guide · 8 min read
Trails, Shooting Lanes and Screening Cover: Laying Out Hunting Land
Lay out hunting land in North Georgia by marking bedding areas and travel routes first, then stands, then access trails, and cut shooting lanes and plots last. This guide covers each piece: narrow lanes cut from the stand, trails routed around bedding, and screening cover left thick along roads, plot edges and property lines.
Start with where deer live, then where you sit
Most hunting tracts we walk around Cumming were cleared in the wrong order. Someone opened a plot where the ground was easy, cut a trail to it from the road, and put a stand wherever the trail ended. The deer bedded somewhere else and crossed the property at night.
Lay it out in this order and the cutting takes care of itself:
- Bedding areas. The thick cover where deer spend the day. These stay as they are.
- Travel routes. The trails, saddles, creek crossings and field edges deer use between bedding and feed.
- Stand sites. Box stands and ladders placed along those routes, with the wind and the sun in mind.
- Access. How you reach each stand without walking through bedding or across the plot.
- The openings. Plots and shooting lanes cut where you can see them from the stand.
Only the last two steps involve a machine. The first three happen on foot, ideally with the leaves down after the season closes, when beds, rubs and worn trails are easy to read.
Shooting lanes: narrow, angled and cut from the stand
A shooting lane is a narrow opening cut out from a stand so you get a clear shot at a deer crossing it. Lanes work best when they run along the angles deer actually travel, so a deer steps into the lane broadside instead of walking straight down it toward you.
- Cut from the stand outward. We set the lane lines with you sitting in the stand or standing at its base, then flag them before the machine starts.
- Keep them narrow. A deer should cross a lane in a step or two. A wide lane turns into a road deer avoid in daylight.
- Clear the understory, keep the canopy. The mulcher grinds the brush, privet and saplings in the lane. Big trees stay unless they block the shot.
- Two or three per stand. Enough to cover the trails you’re watching, without opening the woods around you.
Lanes cut through the understory under standing timber look like an underbrushed strip: a mulch floor, the big trunks still there, and a line of sight you didn’t have before. They grow back from the roots, which we cover further down.

Access trails: reach the stand without being noticed
An access trail gets you and an ATV to the stand quietly, with the wind in your face and without crossing the ground deer use. Route it before you route anything else around the stand.
- Come in from the downwind side. Your scent should blow away from the bedding area and the plot as you walk in.
- Stay off the plot. A trail that crosses the plot to reach the stand spooks every deer feeding on it in the evening.
- Go around bedding, not through it. Even one pass a week through a bedding thicket pushes deer off it.
- Follow the contour on slopes. A trail cut straight up a Piedmont ridge turns into a gully in red clay. We set water bars, angled berms that turn rain off into the woods, on every grade.
- Cross creeks once. Plan one crossing point, and keep the trail out of the streamside zone everywhere else.
Trail work can need county paperwork. Forsyth County counts clearing vegetation as land disturbance, and a project disturbing an acre or more, or any work within 200 feet of a creek, needs a land disturbance permit unless it falls under an exemption such as forestry. Georgia also keeps a 25-foot buffer along state waters, and Forsyth County holds a 50-foot undisturbed buffer plus a 25-foot setback. We check where your trails sit against those lines on the walk. The answer page on ATV and walking trails without a permit has the detail.
Permit thresholds, fees and buffer widths are those published by Forsyth County and the State of Georgia as of November 4, 2026. Confirm current requirements with the issuing authority before work begins. This is not legal advice.
Stand sites: box stands, ladders and the walk in
A box stand needs a level pad, a way to get it there, and a clear view of the plot or the trail it watches. Ladder stands need a straight tree on the right side of the travel route. Both need you to arrive without being seen.
- A level spot for the box. We clear and flatten a small pad for the stand, and leave the brush around its base so the stand doesn’t sit exposed in an open circle.
- A route for the trailer. Box stands go in on a trailer or a tractor. The access trail has to be wide and firm enough to get the stand to its spot once.
- Wind on the travel route. Put the stand downwind of where deer move for the wind you plan to hunt it on. A plot you hunt often may need two stands for two wind directions.
- The evening and morning sun. An evening stand facing west looks into the sun for the last hour. Face it north or east where the plot allows.
Settle the stand sites before anyone cuts a lane. Every lane runs out from a stand, so moving a stand after clearing means cutting new lanes and letting the old ones grow back.
Screening cover: what stays thick
Screening cover is the thick growth that hides the plot, the trail and the stand from deer, from the road and from the neighbors. It is the part of a layout people cut by mistake, because a machine on site makes it tempting to open everything up.
- Along roads and drives. Deer won’t use a plot in daylight if they can see trucks from it, and you don’t want the plot visible from the road.
- Along neighbor lines. Cover on the property line keeps deer on your side and keeps your stands out of view.
- Around the plot edge. A soft, brushy edge gives deer cover to step out from. A hard edge of open woods holds them back until dark.
- Beside the access trail near the stand. The last stretch of trail should run through cover, so deer near the plot can’t watch you climb in.
We flag screening cover on the walk the same way we flag plot corners, and the machine stays out of it. If your tract has no cover where it needs some, the fix is time: leave the strip alone, and briars and sprouts fill it within a season or two.
Bedding areas: marked and left alone
Bedding areas are thickets, cutover patches, briar tangles and the brushy points of ridges where deer lie up during the day. On a Forsyth County tract they are often the privet and honeysuckle thickets along a creek bottom, or a young pine stand too thick to walk through.
Leave them out of the clearing entirely. Mark them on your map and on the ground, and keep machines, trails and lanes out. The one exception is a bedding area that has grown into a solid privet wall with nothing under it. A forester or biologist may prescribe opening parts of it so sprouts and browse come back at deer height. That is habitat work done on purpose, and it gets planned separately from the plot clearing. More on how mulching affects habitat in is forestry mulching good for deer habitat.
A layout, piece by piece
Each part of a hunting layout gets a different treatment. This is how we handle them on a typical tract.
| Feature | What we do | What it leaves |
|---|---|---|
| Food plot | Mulched, stumps handled to fit how you’ll plant | An opening you can lime and seed |
| Shooting lane | Understory mulched in a narrow strip from the stand | A clear line of sight under standing timber |
| Access trail | Cut to machine width, water bars on slope | A quiet route to the stand |
| Stand site | A level spot cleared for a box stand | Room to set the stand and walk to it |
| Screening cover | Flagged and left standing | Thick growth between deer and people |
| Bedding area | Marked on the map, machines kept out | The thicket deer already use |
| Firebreak | Cut to soil or mowed green around the timber | A fire line that doubles as a trail |
Firebreaks earn a place on a hunting tract. A bare or mowed line around a pine stand protects the timber, gives a burn crew a place to work from, and makes a quiet walking route in the season. See firebreak installation.
Mistakes we see on hunting land
- Clearing everything the machine can reach. An open, mulched woods floor looks tidy and holds fewer deer in daylight. Cut the openings you need and stop.
- Lanes too wide. A lane cut to the width of the machine plus a margin each side reads to deer like a road. They cross it at a run, or after dark.
- A trail through the bedding area. Usually because it was the flattest route. A longer trail around it costs a little more and keeps the deer where they are.
- Clearing in the season. A machine running near your stands in the fall moves deer off the spots you cleared. Plot and lane work belongs in late spring and summer. The North Georgia food plot calendar lays out the timing.
- No plan for regrowth. Lanes and trails close in within two seasons if nobody mows them.
Keeping lanes and trails open
Everything you cut grows back. Sweetgum, red maple, privet, blackberry and greenbrier sprout from the roots the spring after clearing. Pines don’t, but there are rarely many pines in a shooting lane. One mowing each summer, before bow season, keeps lanes clear and trails quiet. We do that as bush hogging and maintenance mowing, and you can put it on the same contract as the clearing.
What a layout job costs
Lanes and trails price by length, by how thick the growth is, and by the ground under it. Most of this work is light brush and saplings, so it prices in the lower mulching bands or by machine time.
Rates that apply to layout work
- $1,200 to $2,500
- Per acre, light brush, privet and saplings
- $150 to $300
- Per hour, mulcher with operator
- $1,800 to $3,000
- Machine day rate
- $1,200 to $2,000
- Small-job minimum
Ranges are estimates for Forsyth County and the surrounding area based on job density, terrain, access and acreage. Your written quote is the only price that applies to your property.
Narrow work spread across a tract often goes by the hour or the day, because the machine spends time moving between stands. Putting plots, lanes, trails and firebreaks on one trip saves hauling the machine back. Everything else we do on a hunting tract is on the hunting and timber land page.
Food Plot, Trail and Hunting Land Clearing
Firebreak Installation
Underbrush Clearing: Open the Woods, Keep the Canopy- 1Map it on footBedding, travel routes and stands, marked with the leaves off.
- 2Flag the cutsLanes from each stand, trails, plot corners and the cover that stays.
- 3Clear in summerMulched in place, water bars on slopes, nothing burned.
- 4Mow each summerOne pass before bow season keeps it all open.
Keep reading